CI test: SPH barotropic equation of state#

The barotropic equation of state

\[P = c_{s,0}^2 \rho \left[1 + \left(\frac{\rho}{\rho_0}\right)^{\gamma - 1}\right]\]

is isothermal well below \(\rho_0\) and a polytrope \(P = K \rho^\gamma\) with \(K = c_{s,0}^2 \rho_0^{1-\gamma}\) well above it.

This test evolves the same small periodic setup (a velocity perturbation in a uniform box) with

  • set_eos_barotropic with \(\rho_0 \gg \rho\), compared to set_eos_isothermal(cs0),

  • set_eos_barotropic with \(\rho_0 \ll \rho\), compared to set_eos_polytropic(K, gamma),

and checks that both pairs of runs agree. It also checks that invalid barotropic parameters are rejected.

25 import numpy as np
26
27 import shamrock
28
29 if not shamrock.sys.is_initialized():
30     shamrock.change_loglevel(1)
31     shamrock.sys.init("0:0")
32
33 pmass = 1e-3
34 dr = 0.05
35 bmin = (-0.6, -0.6, -0.6)
36 bmax = (0.6, 0.6, 0.6)
37 t_end = 0.05
38
39 # HCP neighbours are 2 dr apart, the number density is sqrt(2) / (2 dr)^3
40 rho_mean = pmass * np.sqrt(2) / (2 * dr) ** 3
41
42
43 def run(set_eos):
44     ctx = shamrock.Context()
45     ctx.pdata_layout_new()
46
47     model = shamrock.get_Model_SPH(context=ctx, vector_type="f64_3", sph_kernel="M4")
48
49     cfg = model.gen_default_config()
50     cfg.set_self_gravity_none()
51     cfg.set_artif_viscosity_Constant(alpha_u=1.0, alpha_AV=1.0, beta_AV=2.0)
52     set_eos(cfg)
53     cfg.set_particle_mass(pmass)
54     cfg.set_boundary_periodic()
55     model.set_solver_config(cfg)
56
57     model.set_cfl_cour(0.1)
58     model.set_cfl_force(0.1)
59
60     model.init_scheduler(1000, 1)
61     model.resize_simulation_box(bmin, bmax)
62
63     setup = model.get_setup()
64     setup.apply_setup(setup.make_generator_lattice_hcp(dr, bmin, bmax))
65
66     L = bmax[0] - bmin[0]
67
68     def vel_func(r):
69         x, y, z = r
70         return (0.05 * np.sin(2 * np.pi * x / L), 0.0, 0.0)
71
72     model.set_field_value_lambda_f64_3("vxyz", vel_func)
73     model.set_value_in_a_box("uint", "f64", 1.0, bmin, bmax)
74
75     model.timestep()
76     model.evolve_until(t_end)
77
78     vxyz = np.asarray(ctx.collect_data()["vxyz"])
79     # sorted speeds do not depend on the particle ordering
80     return np.sort(np.linalg.norm(vxyz, axis=1))
81
82
83 def compare(name, ref, got, rtol):
84     if ref.shape != got.shape:
85         raise AssertionError(f"{name}: shape mismatch {ref.shape} vs {got.shape}")
86     err = np.max(np.abs(got - ref)) / np.max(np.abs(ref))
87     print(f"{name}: max relative speed difference = {err:.3e} (tolerance {rtol:.1e})")
88     if not err < rtol:
89         raise AssertionError(f"{name}: barotropic run differs from the reference: {err:.3e}")
90
91
92 gamma = 5.0 / 3.0

Isothermal limit: rho0 >> rho

 97 cs0 = 1.0
 98 v_iso = run(lambda cfg: cfg.set_eos_isothermal(cs0))
 99 v_baro_iso = run(lambda cfg: cfg.set_eos_barotropic(cs0=cs0, rho0=1e30, gamma0=gamma))
100 compare("isothermal limit", v_iso, v_baro_iso, 1e-10)
SPH setup: generating particles ...
SPH setup: Nstep = 0 ( 0.0e+00 ) Ntotal = 0 ( 0.0e+00 rank min = 0.0e+00 max = 0.0e+00) rate = 0.000000e+00 N.s^-1
SPH setup: Nstep = 70 ( 7.0e+01 ) Ntotal = 70 ( 7.0e+01 rank min = 8.8e+04 max = 7.0e+01) rate = 7.000000e+01 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 176 ( 1.8e+02 rank min = 1.3e+05 max = 1.8e+02) rate = 1.760000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 294 ( 2.9e+02 rank min = 1.6e+05 max = 2.9e+02) rate = 2.940000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 403 ( 4.0e+02 rank min = 4.8e+05 max = 4.0e+02) rate = 4.030000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 513 ( 5.1e+02 rank min = 1.5e+05 max = 5.1e+02) rate = 5.130000e+02 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 619 ( 6.2e+02 rank min = 8.2e+05 max = 6.2e+02) rate = 6.190000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 737 ( 7.4e+02 rank min = 8.9e+05 max = 7.4e+02) rate = 7.370000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 847 ( 8.5e+02 rank min = 1.4e+05 max = 8.5e+02) rate = 8.470000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 956 ( 9.6e+02 rank min = 6.0e+05 max = 9.6e+02) rate = 9.560000e+02 N.s^-1
SPH setup: Nstep = 115 ( 1.2e+02 ) Ntotal = 1071 ( 1.1e+03 rank min = 6.0e+05 max = 1.1e+03) rate = 1.071000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1192 ( 1.2e+03 rank min = 5.4e+05 max = 1.2e+03) rate = 1.192000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1310 ( 1.3e+03 rank min = 1.3e+05 max = 1.3e+03) rate = 1.310000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1429 ( 1.4e+03 rank min = 6.4e+05 max = 1.4e+03) rate = 1.429000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1550 ( 1.6e+03 rank min = 8.5e+05 max = 1.6e+03) rate = 1.550000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1671 ( 1.7e+03 rank min = 8.8e+05 max = 1.7e+03) rate = 1.671000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1789 ( 1.8e+03 rank min = 6.9e+05 max = 1.8e+03) rate = 1.789000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1908 ( 1.9e+03 rank min = 8.9e+05 max = 1.9e+03) rate = 1.908000e+03 N.s^-1
SPH setup: Nstep = 122 ( 1.2e+02 ) Ntotal = 2030 ( 2.0e+03 rank min = 1.2e+05 max = 2.0e+03) rate = 2.030000e+03 N.s^-1
SPH setup: Nstep = 120 ( 1.2e+02 ) Ntotal = 2150 ( 2.2e+03 rank min = 8.3e+05 max = 2.2e+03) rate = 2.150000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 2268 ( 2.3e+03 rank min = 9.2e+05 max = 2.3e+03) rate = 2.268000e+03 N.s^-1
SPH setup: Nstep = 63 ( 6.3e+01 ) Ntotal = 2331 ( 2.3e+03 rank min = 4.1e+05 max = 2.3e+03) rate = 2.331000e+03 N.s^-1
SPH setup: the generation step took : 0.013693024000000002 s
SPH setup: final particle count = 2331 beginning injection ...
SPH setup: injected         2000 / 2331 =>  85.8% | ranks with patchs = 1 / 1  -> local loop <-
SPH setup: injected         2331 / 2331 => 100.0% | ranks with patchs = 1 / 1  <- global loop -> (msg count : 0)
SPH setup: the injection step took : 0.032361091 s
SPH setup: the setup took : 0.050662324 s
---------------- t = 0, dt = 0 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.09799885899543734 unconverged cnt = 2331
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.10779874489498108 unconverged cnt = 682
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.1185786193844792 unconverged cnt = 36
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0, dt = 9.255285691623669e-05 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 9.255285691623669e-05, dt = 0.0031468192696409913 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.012560635289608792
---------------- t = 0.003239372126557228, dt = 0.002501613489598968 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.005740985616156196, dt = 0.004463790444989298 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.02048626534789981
---------------- t = 0.010204776061145494, dt = 0.0027054239987146797 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.012910200059860173, dt = 0.004251869945085898 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.018840222366621324
---------------- t = 0.01716207000494607, dt = 0.0025114741784108938 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.019673544183356963, dt = 0.003899499114001739 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.014963872969620408
---------------- t = 0.023573043297358702, dt = 0.0023227000126066935 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.025895743309965396, dt = 0.003618392931977634 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.011838616798169554
---------------- t = 0.02951413624194303, dt = 0.0021766395165257243 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03169077575846876, dt = 0.0034079009815905013 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03509867674005926, dt = 0.004128805367701994 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.012886214194963963
---------------- t = 0.03922748210776125, dt = 0.002255085418876398 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04148256752663765, dt = 0.0032938402491943797 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04477640777583203, dt = 0.003910076306337886 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04868648408216991, dt = 0.001313515917830091 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
SPH setup: generating particles ...
SPH setup: Nstep = 0 ( 0.0e+00 ) Ntotal = 0 ( 0.0e+00 rank min = 0.0e+00 max = 0.0e+00) rate = 0.000000e+00 N.s^-1
SPH setup: Nstep = 70 ( 7.0e+01 ) Ntotal = 70 ( 7.0e+01 rank min = 4.2e+05 max = 7.0e+01) rate = 7.000000e+01 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 176 ( 1.8e+02 rank min = 2.7e+05 max = 1.8e+02) rate = 1.760000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 294 ( 2.9e+02 rank min = 2.9e+05 max = 2.9e+02) rate = 2.940000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 403 ( 4.0e+02 rank min = 9.5e+05 max = 4.0e+02) rate = 4.030000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 513 ( 5.1e+02 rank min = 2.8e+05 max = 5.1e+02) rate = 5.130000e+02 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 619 ( 6.2e+02 rank min = 9.7e+05 max = 6.2e+02) rate = 6.190000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 737 ( 7.4e+02 rank min = 1.0e+06 max = 7.4e+02) rate = 7.370000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 847 ( 8.5e+02 rank min = 2.5e+05 max = 8.5e+02) rate = 8.470000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 956 ( 9.6e+02 rank min = 9.5e+05 max = 9.6e+02) rate = 9.560000e+02 N.s^-1
SPH setup: Nstep = 115 ( 1.2e+02 ) Ntotal = 1071 ( 1.1e+03 rank min = 1.1e+06 max = 1.1e+03) rate = 1.071000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1192 ( 1.2e+03 rank min = 1.1e+06 max = 1.2e+03) rate = 1.192000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1310 ( 1.3e+03 rank min = 2.8e+05 max = 1.3e+03) rate = 1.310000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1429 ( 1.4e+03 rank min = 1.1e+06 max = 1.4e+03) rate = 1.429000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1550 ( 1.6e+03 rank min = 1.0e+06 max = 1.6e+03) rate = 1.550000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1671 ( 1.7e+03 rank min = 1.1e+06 max = 1.7e+03) rate = 1.671000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1789 ( 1.8e+03 rank min = 1.1e+06 max = 1.8e+03) rate = 1.789000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1908 ( 1.9e+03 rank min = 1.1e+06 max = 1.9e+03) rate = 1.908000e+03 N.s^-1
SPH setup: Nstep = 122 ( 1.2e+02 ) Ntotal = 2030 ( 2.0e+03 rank min = 2.9e+05 max = 2.0e+03) rate = 2.030000e+03 N.s^-1
SPH setup: Nstep = 120 ( 1.2e+02 ) Ntotal = 2150 ( 2.2e+03 rank min = 1.1e+06 max = 2.2e+03) rate = 2.150000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 2268 ( 2.3e+03 rank min = 1.1e+06 max = 2.3e+03) rate = 2.268000e+03 N.s^-1
SPH setup: Nstep = 63 ( 6.3e+01 ) Ntotal = 2331 ( 2.3e+03 rank min = 6.1e+05 max = 2.3e+03) rate = 2.331000e+03 N.s^-1
SPH setup: the generation step took : 0.008229973 s
SPH setup: final particle count = 2331 beginning injection ...
SPH setup: injected         2000 / 2331 =>  85.8% | ranks with patchs = 1 / 1  -> local loop <-
SPH setup: injected         2331 / 2331 => 100.0% | ranks with patchs = 1 / 1  <- global loop -> (msg count : 0)
SPH setup: the injection step took : 0.028814234 s
SPH setup: the setup took : 0.041017048 s
---------------- t = 0, dt = 0 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.09799885899543734 unconverged cnt = 2331
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.10779874489498108 unconverged cnt = 682
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.1185786193844792 unconverged cnt = 36
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0, dt = 9.255285691623669e-05 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 9.255285691623669e-05, dt = 0.0031468192696409913 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.012560635289608792
---------------- t = 0.003239372126557228, dt = 0.002501613489598968 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.005740985616156196, dt = 0.004463790444989298 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.02048626534789981
---------------- t = 0.010204776061145494, dt = 0.0027054239987146797 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.012910200059860173, dt = 0.004251869945085898 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.018840222366621324
---------------- t = 0.01716207000494607, dt = 0.0025114741784108938 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.019673544183356963, dt = 0.003899499114001739 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.014963872969620408
---------------- t = 0.023573043297358702, dt = 0.0023227000126066935 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.025895743309965396, dt = 0.003618392931977634 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.011838616798169554
---------------- t = 0.02951413624194303, dt = 0.0021766395165257243 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03169077575846876, dt = 0.0034079009815905013 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03509867674005926, dt = 0.004128805367701994 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.012886214194963963
---------------- t = 0.03922748210776125, dt = 0.002255085418876398 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04148256752663765, dt = 0.0032938402491943797 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04477640777583203, dt = 0.003910076306337886 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04868648408216991, dt = 0.001313515917830091 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
isothermal limit: max relative speed difference = 0.000e+00 (tolerance 1.0e-10)

Adiabatic limit: rho0 << rho, choosing cs0 such that K = 1 (the sound speed stays ~1)

The barotropic pressure differs from the polytrope by a relative (rho0 / rho)^(gamma - 1)

107 K = 1.0
108 rho0 = 1e-12 * rho_mean
109 cs0_poly = np.sqrt(K * rho0 ** (gamma - 1))
110
111 v_poly = run(lambda cfg: cfg.set_eos_polytropic(K, gamma))
112 v_baro_poly = run(lambda cfg: cfg.set_eos_barotropic(cs0=cs0_poly, rho0=rho0, gamma0=gamma))
113 compare("adiabatic limit", v_poly, v_baro_poly, 1e-6)
SPH setup: generating particles ...
SPH setup: Nstep = 0 ( 0.0e+00 ) Ntotal = 0 ( 0.0e+00 rank min = 0.0e+00 max = 0.0e+00) rate = 0.000000e+00 N.s^-1
SPH setup: Nstep = 70 ( 7.0e+01 ) Ntotal = 70 ( 7.0e+01 rank min = 7.1e+04 max = 7.0e+01) rate = 7.000000e+01 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 176 ( 1.8e+02 rank min = 1.3e+05 max = 1.8e+02) rate = 1.760000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 294 ( 2.9e+02 rank min = 1.5e+05 max = 2.9e+02) rate = 2.940000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 403 ( 4.0e+02 rank min = 4.1e+05 max = 4.0e+02) rate = 4.030000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 513 ( 5.1e+02 rank min = 1.3e+05 max = 5.1e+02) rate = 5.130000e+02 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 619 ( 6.2e+02 rank min = 5.6e+05 max = 6.2e+02) rate = 6.190000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 737 ( 7.4e+02 rank min = 6.8e+05 max = 7.4e+02) rate = 7.370000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 847 ( 8.5e+02 rank min = 1.3e+05 max = 8.5e+02) rate = 8.470000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 956 ( 9.6e+02 rank min = 7.4e+05 max = 9.6e+02) rate = 9.560000e+02 N.s^-1
SPH setup: Nstep = 115 ( 1.2e+02 ) Ntotal = 1071 ( 1.1e+03 rank min = 4.9e+05 max = 1.1e+03) rate = 1.071000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1192 ( 1.2e+03 rank min = 4.6e+05 max = 1.2e+03) rate = 1.192000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1310 ( 1.3e+03 rank min = 1.3e+05 max = 1.3e+03) rate = 1.310000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1429 ( 1.4e+03 rank min = 7.4e+05 max = 1.4e+03) rate = 1.429000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1550 ( 1.6e+03 rank min = 6.8e+05 max = 1.6e+03) rate = 1.550000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1671 ( 1.7e+03 rank min = 7.6e+05 max = 1.7e+03) rate = 1.671000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1789 ( 1.8e+03 rank min = 6.3e+05 max = 1.8e+03) rate = 1.789000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1908 ( 1.9e+03 rank min = 7.2e+05 max = 1.9e+03) rate = 1.908000e+03 N.s^-1
SPH setup: Nstep = 122 ( 1.2e+02 ) Ntotal = 2030 ( 2.0e+03 rank min = 1.1e+05 max = 2.0e+03) rate = 2.030000e+03 N.s^-1
SPH setup: Nstep = 120 ( 1.2e+02 ) Ntotal = 2150 ( 2.2e+03 rank min = 7.4e+05 max = 2.2e+03) rate = 2.150000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 2268 ( 2.3e+03 rank min = 8.6e+05 max = 2.3e+03) rate = 2.268000e+03 N.s^-1
SPH setup: Nstep = 63 ( 6.3e+01 ) Ntotal = 2331 ( 2.3e+03 rank min = 3.7e+05 max = 2.3e+03) rate = 2.331000e+03 N.s^-1
SPH setup: the generation step took : 0.013420126000000001 s
SPH setup: final particle count = 2331 beginning injection ...
SPH setup: injected         2000 / 2331 =>  85.8% | ranks with patchs = 1 / 1  -> local loop <-
SPH setup: injected         2331 / 2331 => 100.0% | ranks with patchs = 1 / 1  <- global loop -> (msg count : 0)
SPH setup: the injection step took : 0.03501319 s
SPH setup: the setup took : 0.053025123 s
---------------- t = 0, dt = 0 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.09799885899543734 unconverged cnt = 2331
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.10779874489498108 unconverged cnt = 682
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.1185786193844792 unconverged cnt = 36
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0, dt = 6.277945852849434e-05 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 6.277945852849434e-05, dt = 0.0021345213423489785 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.002197300800877473, dt = 0.0034438413780923834 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.017950048495129278
---------------- t = 0.005641142178969856, dt = 0.0020927070362889103 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.007733849215258767, dt = 0.0032850168036234863 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.015812191142968283
---------------- t = 0.011018866018882252, dt = 0.0019486631377921082 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.01296752915667436, dt = 0.0030290735775780494 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.01270127501075283
---------------- t = 0.015996602734252408, dt = 0.0018127825353165812 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.01780938526956899, dt = 0.00282449510933336 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.010198642068520647
---------------- t = 0.020633880378902347, dt = 0.0016984325167797556 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.0223323128956821, dt = 0.0026578074050630286 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.02499012030074513, dt = 0.003215804002377956 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.011178545544621778
---------------- t = 0.028205924303123086, dt = 0.001760067056772007 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.029965991359895094, dt = 0.002575576618736964 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03254156797863206, dt = 0.003064109154448612 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03560567713308067, dt = 0.003342588586698593 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03894826571977926, dt = 0.0034924013309094535 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04244066705068871, dt = 0.0035664638904123413 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04600713094110105, dt = 0.003597945978507056 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04960507691960811, dt = 0.00039492308039189294 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
SPH setup: generating particles ...
SPH setup: Nstep = 0 ( 0.0e+00 ) Ntotal = 0 ( 0.0e+00 rank min = 0.0e+00 max = 0.0e+00) rate = 0.000000e+00 N.s^-1
SPH setup: Nstep = 70 ( 7.0e+01 ) Ntotal = 70 ( 7.0e+01 rank min = 4.5e+05 max = 7.0e+01) rate = 7.000000e+01 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 176 ( 1.8e+02 rank min = 2.2e+05 max = 1.8e+02) rate = 1.760000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 294 ( 2.9e+02 rank min = 2.5e+05 max = 2.9e+02) rate = 2.940000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 403 ( 4.0e+02 rank min = 9.2e+05 max = 4.0e+02) rate = 4.030000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 513 ( 5.1e+02 rank min = 2.1e+05 max = 5.1e+02) rate = 5.130000e+02 N.s^-1
SPH setup: Nstep = 106 ( 1.1e+02 ) Ntotal = 619 ( 6.2e+02 rank min = 8.4e+05 max = 6.2e+02) rate = 6.190000e+02 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 737 ( 7.4e+02 rank min = 1.1e+06 max = 7.4e+02) rate = 7.370000e+02 N.s^-1
SPH setup: Nstep = 110 ( 1.1e+02 ) Ntotal = 847 ( 8.5e+02 rank min = 2.2e+05 max = 8.5e+02) rate = 8.470000e+02 N.s^-1
SPH setup: Nstep = 109 ( 1.1e+02 ) Ntotal = 956 ( 9.6e+02 rank min = 9.1e+05 max = 9.6e+02) rate = 9.560000e+02 N.s^-1
SPH setup: Nstep = 115 ( 1.2e+02 ) Ntotal = 1071 ( 1.1e+03 rank min = 1.0e+06 max = 1.1e+03) rate = 1.071000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1192 ( 1.2e+03 rank min = 1.1e+06 max = 1.2e+03) rate = 1.192000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1310 ( 1.3e+03 rank min = 2.4e+05 max = 1.3e+03) rate = 1.310000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1429 ( 1.4e+03 rank min = 1.1e+06 max = 1.4e+03) rate = 1.429000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1550 ( 1.6e+03 rank min = 1.1e+06 max = 1.6e+03) rate = 1.550000e+03 N.s^-1
SPH setup: Nstep = 121 ( 1.2e+02 ) Ntotal = 1671 ( 1.7e+03 rank min = 1.1e+06 max = 1.7e+03) rate = 1.671000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 1789 ( 1.8e+03 rank min = 1.2e+06 max = 1.8e+03) rate = 1.789000e+03 N.s^-1
SPH setup: Nstep = 119 ( 1.2e+02 ) Ntotal = 1908 ( 1.9e+03 rank min = 1.2e+06 max = 1.9e+03) rate = 1.908000e+03 N.s^-1
SPH setup: Nstep = 122 ( 1.2e+02 ) Ntotal = 2030 ( 2.0e+03 rank min = 2.6e+05 max = 2.0e+03) rate = 2.030000e+03 N.s^-1
SPH setup: Nstep = 120 ( 1.2e+02 ) Ntotal = 2150 ( 2.2e+03 rank min = 1.2e+06 max = 2.2e+03) rate = 2.150000e+03 N.s^-1
SPH setup: Nstep = 118 ( 1.2e+02 ) Ntotal = 2268 ( 2.3e+03 rank min = 1.2e+06 max = 2.3e+03) rate = 2.268000e+03 N.s^-1
SPH setup: Nstep = 63 ( 6.3e+01 ) Ntotal = 2331 ( 2.3e+03 rank min = 6.2e+05 max = 2.3e+03) rate = 2.331000e+03 N.s^-1
SPH setup: the generation step took : 0.010047348000000001 s
SPH setup: final particle count = 2331 beginning injection ...
SPH setup: injected         2000 / 2331 =>  85.8% | ranks with patchs = 1 / 1  -> local loop <-
SPH setup: injected         2331 / 2331 => 100.0% | ranks with patchs = 1 / 1  <- global loop -> (msg count : 0)
SPH setup: the injection step took : 0.032996801 s
SPH setup: the setup took : 0.046904673 s
---------------- t = 0, dt = 0 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.09799885899543734 unconverged cnt = 2331
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.10779874489498108 unconverged cnt = 682
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: smoothing length is not converged, rerunning the iterator ...    [Smoothinglength][rank=0]
     largest h = 0.1185786193844792 unconverged cnt = 36
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0, dt = 6.277945836822782e-05 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 6.277945836822782e-05, dt = 0.0021345213368997667 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.0021973007952679944, dt = 0.003443841368949804 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.017950048591669807
---------------- t = 0.005641142164217798, dt = 0.0020927070304981045 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.007733849194715902, dt = 0.003285016793301358 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.015812191223307306
---------------- t = 0.011018865988017261, dt = 0.0019486631314653822 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.012967529119482643, dt = 0.003029073567584856 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.012701275063256977
---------------- t = 0.0159966026870675, dt = 0.0018127825287304717 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.01780938521579797, dt = 0.002824495098958605 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.010198642099160982
---------------- t = 0.020633880314756575, dt = 0.00169843251046018 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.022332312825216756, dt = 0.0026578073950987505 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.024990120220315507, dt = 0.003215803990197971 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
Warning: the corrector tolerance are broken the step will be re rerunned      [BasicGasSPH][rank=0]
    eps_v = 0.011178545570919938
---------------- t = 0.02820592421051348, dt = 0.0017600670500431477 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.029965991260556626, dt = 0.0025755766088448196 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03254156786940145, dt = 0.0030641091426134226 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03560567701201487, dt = 0.0033425885737203894 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.03894826558573526, dt = 0.0034924013172949646 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.04244066690303023, dt = 0.0035664638764735636 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.046007130779503795, dt = 0.003597945964430602 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
---------------- t = 0.0496050767439344, dt = 0.00039492325606560463 ----------------
Warning: High interface/patch volume ratio.                                  [InterfaceGen][rank=0]
    This can lead to high mpi overhead, try to increase the patch split crit
adiabatic limit: max relative speed difference = 6.654e-09 (tolerance 1.0e-06)

Invalid parameters must be rejected when the config is set

118 for bad in [
119     dict(cs0=-1.0, rho0=1.0, gamma0=gamma),
120     dict(cs0=1.0, rho0=0.0, gamma0=gamma),
121     dict(cs0=1.0, rho0=1.0, gamma0=1.0),
122 ]:
123     ctx = shamrock.Context()
124     ctx.pdata_layout_new()
125     model = shamrock.get_Model_SPH(context=ctx, vector_type="f64_3", sph_kernel="M4")
126     cfg = model.gen_default_config()
127     cfg.set_eos_barotropic(**bad)
128     try:
129         model.set_solver_config(cfg)
130     except ValueError as e:
131         print(f"rejected {bad} as expected: {type(e).__name__}")
132     else:
133         raise AssertionError(f"invalid barotropic parameters {bad} were accepted")
134
135 print("barotropic EOS test passed")
Error: Exception created :                                                      [Exception][rank=0]
barotropic EOS requires cs0 > 0, rho0 > 0 and gamma0 > 1, got cs0 = -1, rho0 = 1, gamma0 = 1.6666666666666667
---- Source Location ----
/opt/Shamrock_src/src/shammodels/sph/include/shammodels/sph/SolverConfig.hpp:1265:17
call = void shammodels::sph::SolverConfig<hipsycl::sycl::vec<double, 3>, shammath::M4>::check_config() [Tvec = hipsycl::sycl::vec<double, 3>, SPHKernel = shammath::M4]
stacktrace :
  -> process identifier: ad7362c1cd7e (world rank: 0, local rank: Unknown)
Memory usage & performance info:

    World infos :
        World size = 1
        World rank = 0
    Device infos :
        Device name = AdaptiveCpp OpenMP host device
    Allocs :
        max_allocated_byte_host = 5.29 MB
        max_allocated_byte_device = 1.26 GB
        max_allocated_byte_shared = 0.00 B
        allocated_byte_host = 0.00 B
        allocated_byte_device = 331.38 MB
        allocated_byte_shared = 0.00 B


-------------------------

---- Source Location ----
/opt/Shamrock_src/src/shambase/include/shambase/exception.hpp:133:15
call = void shambase::throw_with_loc(std::string, SourceLocation) [ExcptTypes = std::invalid_argument]
stacktrace :
  -> process identifier: ad7362c1cd7e (world rank: 0, local rank: Unknown)
Memory usage & performance info:

    World infos :
        World size = 1
        World rank = 0
    Device infos :
        Device name = AdaptiveCpp OpenMP host device
    Allocs :
        max_allocated_byte_host = 5.29 MB
        max_allocated_byte_device = 1.26 GB
        max_allocated_byte_shared = 0.00 B
        allocated_byte_host = 0.00 B
        allocated_byte_device = 331.38 MB
        allocated_byte_shared = 0.00 B


-------------------------

rejected {'cs0': -1.0, 'rho0': 1.0, 'gamma0': 1.6666666666666667} as expected: ValueError
Error: Exception created :                                                      [Exception][rank=0]
barotropic EOS requires cs0 > 0, rho0 > 0 and gamma0 > 1, got cs0 = 1, rho0 = 0, gamma0 = 1.6666666666666667
---- Source Location ----
/opt/Shamrock_src/src/shammodels/sph/include/shammodels/sph/SolverConfig.hpp:1265:17
call = void shammodels::sph::SolverConfig<hipsycl::sycl::vec<double, 3>, shammath::M4>::check_config() [Tvec = hipsycl::sycl::vec<double, 3>, SPHKernel = shammath::M4]
stacktrace :
  -> process identifier: ad7362c1cd7e (world rank: 0, local rank: Unknown)
Memory usage & performance info:

    World infos :
        World size = 1
        World rank = 0
    Device infos :
        Device name = AdaptiveCpp OpenMP host device
    Allocs :
        max_allocated_byte_host = 5.29 MB
        max_allocated_byte_device = 1.26 GB
        max_allocated_byte_shared = 0.00 B
        allocated_byte_host = 0.00 B
        allocated_byte_device = 331.38 MB
        allocated_byte_shared = 0.00 B


-------------------------

---- Source Location ----
/opt/Shamrock_src/src/shambase/include/shambase/exception.hpp:133:15
call = void shambase::throw_with_loc(std::string, SourceLocation) [ExcptTypes = std::invalid_argument]
stacktrace :
  -> process identifier: ad7362c1cd7e (world rank: 0, local rank: Unknown)
Memory usage & performance info:

    World infos :
        World size = 1
        World rank = 0
    Device infos :
        Device name = AdaptiveCpp OpenMP host device
    Allocs :
        max_allocated_byte_host = 5.29 MB
        max_allocated_byte_device = 1.26 GB
        max_allocated_byte_shared = 0.00 B
        allocated_byte_host = 0.00 B
        allocated_byte_device = 331.38 MB
        allocated_byte_shared = 0.00 B


-------------------------

rejected {'cs0': 1.0, 'rho0': 0.0, 'gamma0': 1.6666666666666667} as expected: ValueError
Error: Exception created :                                                      [Exception][rank=0]
barotropic EOS requires cs0 > 0, rho0 > 0 and gamma0 > 1, got cs0 = 1, rho0 = 1, gamma0 = 1
---- Source Location ----
/opt/Shamrock_src/src/shammodels/sph/include/shammodels/sph/SolverConfig.hpp:1265:17
call = void shammodels::sph::SolverConfig<hipsycl::sycl::vec<double, 3>, shammath::M4>::check_config() [Tvec = hipsycl::sycl::vec<double, 3>, SPHKernel = shammath::M4]
stacktrace :
  -> process identifier: ad7362c1cd7e (world rank: 0, local rank: Unknown)
Memory usage & performance info:

    World infos :
        World size = 1
        World rank = 0
    Device infos :
        Device name = AdaptiveCpp OpenMP host device
    Allocs :
        max_allocated_byte_host = 5.29 MB
        max_allocated_byte_device = 1.26 GB
        max_allocated_byte_shared = 0.00 B
        allocated_byte_host = 0.00 B
        allocated_byte_device = 331.38 MB
        allocated_byte_shared = 0.00 B


-------------------------

---- Source Location ----
/opt/Shamrock_src/src/shambase/include/shambase/exception.hpp:133:15
call = void shambase::throw_with_loc(std::string, SourceLocation) [ExcptTypes = std::invalid_argument]
stacktrace :
  -> process identifier: ad7362c1cd7e (world rank: 0, local rank: Unknown)
Memory usage & performance info:

    World infos :
        World size = 1
        World rank = 0
    Device infos :
        Device name = AdaptiveCpp OpenMP host device
    Allocs :
        max_allocated_byte_host = 5.29 MB
        max_allocated_byte_device = 1.26 GB
        max_allocated_byte_shared = 0.00 B
        allocated_byte_host = 0.00 B
        allocated_byte_device = 331.38 MB
        allocated_byte_shared = 0.00 B


-------------------------

rejected {'cs0': 1.0, 'rho0': 1.0, 'gamma0': 1.0} as expected: ValueError
barotropic EOS test passed

Total running time of the script: (0 minutes 19.941 seconds)

Estimated memory usage: 218 MB

Gallery generated by Sphinx-Gallery